Recovery
Breaking Strength: 52,300 lbs.1-1/4" x 20' This rope is custom made 4x4 Vans, MB Sprinter, VW Crafter, MAN TGE and Land Cruiser 79, Dodge RAM
The Life Guard is a high performance chafe guard for your Bubba Rope®. Life Guard protects your Bubba Rope® from coming in direct contact with hard or abrasive surfaces during your recovery process
7/8" X 20' BUBBA BLUE EYES To be used with Wrangler, Defender, Hilux, Ranger, D-Max , Amarok and similar sized vehicles
7/8" x 10' BUBBA EXTENSION GRN EYES
7/8" X 30' BUBBA RED EYES ' (rated for Defender, Wrangler, and one tonne Pick-up trucks)
The Fast Fid is a rope splicing tool designed for rapid repairing/splicing of synthetic winch lines.
Eliminate the conventional winch hook and replace it with a safer and stronger FlatLink shackle thimble and D-ring. The FlatLink shackle mount is the Industry’s first folding shackle mount for recovery winches. With less than 1.75 inches of thickness, the Flatlink will work with all roller fairlead license plate mounting brackets.
The FlatLink E (Expert) is a variation of our popular foldable standard FlatLink winch shackle mount. The FlatLink E provides a means to eliminate the conventional winch hook and replace it with a safer and more secure screw pin shackle resulting in a CLOSED SYSTEM WINCHING operation. The large pear shaped shackle mounting hole allows for attachment to either the pin or bow end of common screw pin shackles, as well as common OEM recovery points.
GATOR-JAW (MINI) SOFT SHACKLES 1/4" (pack of 2)
New! Stronger Than Steel! Breaking Strength: 32,000 lbs! Gator-Jaw® synthetic shackles are made from Plasma® rope which is the highest strength synthetic rope available. These superior tow rope connectors are stronger than comparable steel
Factor 55 introduces a new line of Aluminum Hawse Fairleads. The 1.0 and 1.5 fairleads are CNC machined from 1 and 1.5 inch thick USA 6000 series aluminum bar. The industry standard fairlead thickness is .75 inches thick. The thicker aluminum bar results in a larger outer fillet radius for the synthetic rope to slide against. This results in less stress on the rope fibers during high angular pulls, increasing the life of your synthetic rope. The 1.0 and 1.5 fairleads are the industry’s first Hawse fairleads compatible with larger ½ inch diameter rope tube thimbles. The rope slot height opening is taller to allow the larger ½” tube thimbles to pass through. There is also a machined outer corner chamfer to reduce rope stress for those than plan on using the winch as a front suspension “suck down” device. These fairleads come in a durable MIL-A-8625F TYPE III gun metal gray hard anodized finish with a laser engraved logo. What is the best surface finish for Hawse aluminum fairleads? Without a doubt it is a Type III hard anodized coating. Not cosmetic Type II anodized finishes, not powder coated, and not raw or polished aluminum. Why? Because a hard coating can resist the abrasion damage from a dirty/gritty synthetic winch rope rubbing across it. Especially during extreme side pulls where rope fiber stresses are extremely high. A Mil-A-8625 Type III hard anodized finish leaves a .002” thick Al2O3 ceramic coating that is in the top 5 hardest materials known to mankind (See chart under Corundum/Sapphire). Not too far away from diamond hardness actually. Another valuable material property from hard anodized coatings are the low coefficients of friction. Low friction = lower rope heat. Only drawback? Hard anodizing is not offered in typical bright and fancy anodized colors. All Factor 55 fairleads only come in Mil-A-8625 hard gray finishes. Not fancy, but it is the proper finish to extend the life of your synthetic rope. Overall Dimension: 12.35″ x 3.25″ Standard 10″ Bolt Mount Spacing For synthetic winch rope only. *NOTE- Fairleads DO NOT come with mounting hardware.
Factor 55 introduces a new line of Aluminum Hawse Fairleads. The 1.0 and 1.5 fairleads are CNC machined from 1 and 1.5 inch thick USA 6000 series aluminum bar. The industry standard fairlead thickness is .75 inches thick. The thicker aluminum bar results in a larger outer fillet radius for the synthetic rope to slide against. This results in less stress on the rope fibers during high angular pulls, increasing the life of your synthetic rope. The 1.0 and 1.5 fairleads are the industry’s first Hawse fairleads compatible with larger ½ inch diameter rope tube thimbles. The rope slot height opening is taller to allow the larger ½” tube thimbles to pass through. There is also a machined outer corner chamfer to reduce rope stress for those than plan on using the winch as a front suspension “suck down” device. These fairleads come in a durable MIL-A-8625F TYPE III gun metal gray hard anodized finish with a laser engraved logo. What is the best surface finish for Hawse aluminum fairleads? Without a doubt it is a Type III hard anodized coating. Not cosmetic Type II anodized finishes, not powder coated, and not raw or polished aluminum. Why? Because a hard coating can resist the abrasion damage from a dirty/gritty synthetic winch rope rubbing across it. Especially during extreme side pulls where rope fiber stresses are extremely high. A Mil-A-8625 Type III hard anodized finish leaves a .002” thick Al2O3 ceramic coating that is in the top 5 hardest materials known to mankind (See chart under Corundum/Sapphire). Not too far away from diamond hardness actually. Another valuable material property from hard anodized coatings are the low coefficients of friction. Low friction = lower rope heat. Only drawback? Hard anodizing is not offered in typical bright and fancy anodized colors. All Factor 55 fairleads only come in Mil-A-8625 hard gray finishes. Not fancy, but it is the proper finish to extend the life of your synthetic rope. Overall Dimension: 12.35″ x 3.25″ Standard 10″ Bolt Mount Spacing For synthetic winch rope only. *NOTE- Fairleads DO NOT come with mounting hardware.
PRODUCT DESCRIPTION NOW AVAILABLE IN US MILITARY/FEDERAL STANDARD OD GREEN 34094 Use your receiver as a recovery tow point. Lightweight precision CNC machined 6000 series aluminum Weighs only 1.9 pounds. Steel versions weigh up to 8 pounds Rated at 9500 pounds Ultimate failure at 51,000 pounds Fits standard 2 inch receivers Fits common ¾ screw pin shackles/D-Rings Anodized or powder coated for oxidation protection MADE IN USA WARNING: Never exceed factory receiver hitch pull rating Always use a quality steel alloy 5/8” hitch pin Always pull in line with the hitch, do not bind or side load the shackle
Breaking Strength: 74,000 lbs.!1-1/2" x 20' Jumbo Bubba is a mega snatch rope that is so strong it can safely pull a full size 18ton truck out of the muck! Monster trucks, this is the rope for you! Comes with its own mesh duffle bag for easy carrying and storing
Breaking Strength: 74,000 lbs.1-1/2" x 30' Jumbo Bubba is a mega snatch rope that is so strong it can safely pull a full size dump truck out of the muck! Monster trucks, this is the rope for you! Comes with its own mesh duffle bag
The Life Guard is a high performance chafe guard for your Bubba Rope®. Life Guard protects your Bubba Rope® from coming in direct contact with hard or abrasive surfaces during your recovery process
1/2" X 20' LIL' BUBBA YELLOW EYES
Replace conventional winch hooks with the new safer, stronger, and smarter Factor 55 ProLink shackle mount.
The Factor 55 ProLink XXL is the largest and strongest ProLink winch shackle mount in production. The ProLink XXL provides winch owners with a means to replace the conventional winch hook with a safer and stronger screw pin shackle/D-ring. Originally designed for military 24,000 pound winch applications, the ProLink XXL is now available to the general public.
All our winch lines are coated with a heavy Gator-ized and vinyl rope armor resulting Best fit: winches with 8k to 12k lbs. capacity
3/8" X 25' SYNTHETIC WINCH LINE EXTENTION
3/8" X 50' SYNTHETIC WINCH LINE EXTENTION
The worlds safest winch hook. Featuring Industry first Closed System Shackle Mount hole machined into the body of the hook, safety latch retraction pocket resulting in a clear throat opening, integrated secondary safety latch locking feature-latch locking pin stored in the body of the UltraHook which can be removed and inserted in to the hook tip, locking the latch into place.
The worlds safest winch hook. Featuring Industry first Closed System Shackle Mount hole machined into the body of the hook, safety latch retraction pocket resulting in a clear throat opening, integrated secondary safety latch locking feature-latch locking pin stored in the body of the UltraHook which can be removed and inserted in to the hook tip, locking the latch into place.